HOW TO DO IF YOUR HOT WATER SYSTEM ABRUPTLY HALTS WORKING: TIPS

How to Do If Your Hot Water System Abruptly Halts Working: Tips

How to Do If Your Hot Water System Abruptly Halts Working: Tips

Blog Article

About This

Everyone has their own way of thinking with regards to What Would Cause My Electric Water Heater to Stop Working?.



Many modern residences take advantage of an electrical hot water heater for their heating unit, as a result of its benefit as well as ease of use. However, similar to any other electric home appliances, issues may develop with its usage, unexpectedly. It can be really aggravating to wake up to a cold shower instead of a hot one or having your bath with water that isn't warm adequate and even as well hot. Whatever the instance might be, hot water heater issues can be quite nerve-racking. Luckily, we have actually made a listing of possible services to your water heater problems. There are a number of factors that can trigger many of these troubles, it could be an issue with the power supply, the electric heating element, or the thermostat. Before doing anything, guarantee you shut off the main power supply for safety and security. Whatever the trouble is, getting it dealt with ought to not posture excessive of an issue if you adhere to these steps:

Examine Your Power Supply:


As fundamental as this may appear, it is very essential. Without sufficient power, your hot water heater will not operate. So the first thing to do when your water unexpectedly stops working is to confirm that it isn't a power trouble. Inspect if the fuse is burnt out or the circuit breaker stumbled. If the circuit breaker is the problem, simply turn it on and off again. Change any damaged or damaged fuse. Evaluate the device with power after these changes to see if it's currently functioning.

Check the Burner in the Water Heater:


If it's not a power issue, after that try taking a look at your burner if it is still working. Check each of your burner to make sure the problem isn't with any of them. If any one of them is malfunctioning, replace that component and then inspect whether the warm water is back on.

Inspect Your Thermostat:


If your hot water heater still isn't functioning or the water appearing isn't warm sufficient, you may require to examine the temperature level settings on your top thermostat. Ensure the breaker is turned off prior to doing anything. Open the gain access to panel as well as press the red switch for temperature level reset over the thermostat. This ought to help heat the water. Transform the circuit breaker back on and check if the issue has been settled.

Call A Professional:


If after replacing all defective components and resetting your temperature, the water heater still isn't working, you may require to call a specialist plumber for a professional opinion. The issue with your heater could be that the hot and cold taps have been changed or it may be undersized for the quantity of warm water required in your house. Whatever the instance may be, a specialist plumber would assist solve the problem.

Final thought


Hot water heater troubles are not always significant. Most of them are due to minor problems like a blown fuse or worn-out heating element. Replacing the malfunctioning parts ought to suffice. Nonetheless, if you are still incapable to fix the trouble, give a call to your nearby plumber to find to get it repaired.

8 possible reasons why you have no Hot Water


Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.


Water Leak


Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.



Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.


Gas Heater: Gas Leak


If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.


Gas Heater: Pilot Light Problems


There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.



Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.


Gas Heater: Faulty Thermocouple


The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.


Electric Heater: Breaker Blues


Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.


Electric Heater: Reaching The Limit


If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.


Electric Heater: Heating Element


If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/



Do you like reading about No Hot Water — Water Heater Repair? Place feedback down the page. We will be glad to listen to your responses about this blog. In hopes that you visit us again before long. Do you know about someone else who is occupied with the niche? Be sure share it. We love reading our article about Hot Water Heater Repair.


Today's problem, today's fix!

Report this page